CO2 Cutting and Engraving Machines
5 - Instalación software RDworks / Daniel
Para instalar el programa RDworks siga los siguientes pasos PASO 1 descargue el programa versión 8.01.60 de este enlace https://www.dropbox.com/sh/e3444th055hvq5c/AAAtZEqaCp3Of27V7OMog-w8a?dl=0 enlace de la version RDworks V 8.0.1.61 ...
Conexión Eléctrica del chiller CW5200 / Diego - Daniel
Conexión Eléctrica del Chiller CW5200 -CW5000
Electric Connection Chiller CW5200 - CW5000 110V AC / Diego - Daniel
Electric Connection Chiller CW5000 - CW5200 AC 110V
Troubleshooting Chiller Cw5000 - Cw5200 turned on but unelectrified / Daniel
When the chiller is turned on but unelectrified, these following steps help you to troubleshoot Step 1 Check the wires from power cord to the power swich are well connected link of the video ...
Simple Troubleshooting Chiller C5000 - CW5200 / Daniel
SIMPLE TROUBLESHOOTING FOR CHILLER CW5000 SERIES
RDCMarkvision installation and Camera Calibration with Ruida RDV6442G controller / Daniel
Process of the SV300 Camera calibration in Versa machine with Ruida RDV6442G Or RDV6445G Controller. Follow these steps to perform the installation of the RDCMarvision software and calibrate the SV300 camera Step 1 Download and Install the software ...
Aufero Laser 1 Diode Laser Machine video playlist / Daniel
Aufero Laser 1 Diode Laser Machine In the next link, you can see the youtube video playlist for the machine https://www.youtube.com/watch?v=sTXwHu0cfBE&list=PLCvoW8cWgVweZDs3P4-Sw_oyouuw1nR_S
4 pin aviation plug size GX20 to connect the rotary in the star machine / Daniel
GX20 5/8" or 16mm is the size for the 4 pin aviation plug 4 -pin Male plug diameter 15mm 4-pin female plug 15mm GX20 Dimensions and Pins Position for the GX20 Male & Female plug
Star machine auxiliary equipment connections / Daniel
For the dual chiller inlet use only one inlet A, loop a hose in inlet B and outlet B. filled with distilled water until reaching the green level on the gauge. connect the alarm cable in the back of the chiller as shown in the photo below Check the ...
0 - The laser beam mark should be in the center of the hole in the laser head / Daniel
To see how the calibration is, we must observe that the mark of the laser beam is in the center of the hole in the laser head, if the two marks overlap but are above the center, it means that the height of the tube is above of the height of the laser ...
Camera Calibration in WF 300W Ruida RDV6442G controller / Daniel
Process of the Camera calibration in Workforce 300W with Ruida RDV6442G Controller. Follow these steps to perform the installation of the RDCMarvision software and Camera Calibration Step 1 Download and Install the software RDCMarkvision V. ...
Troubleshooting for chiller CW5000 - CW5200 / Daniel
Source: Teyuchiller.com
Ramp test in a CO2 machine / Daniel
To do the Ramp test in a CO2 Machine follow the steps Step 1 Place a piece of wood to make the ramp and cut a line on the sheet as the image Step 2 check the thin line and put the laserhead in that position of the sheet Step 3 Measure the distance ...
Laser path of Versa Dual Max Machine / Daniel
Laser beam Alignment in Dual Max Machine / Daniel
Laser beam Alignment in Versa Dual Max Machine First of all, you need to level the machine and both the glass and RF laser tube, next step is to calibrate the mirrors, So in the next videos, we show you how to do it. Check the alignment in the ...
Dual Max Laser Head´s Mirror screw movements / Daniel
Installing the lens in a CO2 Star Machine / Daniel
Different positions of the lenses inside the barrel Focal Length of lenses Different positions of the lens in the barrel Position of the lens inside the barrel, Remember the convex part must be place facing the mirror, flat part to the material ...
5 - RDworks software installation / Daniel
To install the RDWorks Software follow the steps Step 1 Download the software Version 8.01.60 from this link (copy and paste) https://www.dropbox.com/sh/e3444th055hvq5c/AAAtZEqaCp3Of27V7OMog-w8a?dl=0 link of the version RDworks V 8.0.1.61 ...
Laser Power supply connection with potentiometer / Daniel
Laser Power Supply Connection Without potentiometer / Daniel
Loading the rotary parameters from Lightburn software / Daniel
To Load the file that has the parameters for the rotary attachment follow the next steps Check this video to check the procedure https://www.dropbox.com/s/7xy9j12d91w2az0/rotary%20parameters%20from%20lightburn.mp4?dl=0 Step 1 Go to Edit menu and ...
Engraving and Cutting Acrylic material / Daniel
Acrylic is produced in two basic versions, , cast (GS) and extruded (XT). The different production methods used to create these materials leave the finished product with different material properties. . Cast acrylic is produced by mixing the ...
00 - Check the mirror 3 to the nozzle alignment / Daniel
To see how the calibration is, it should be noted that the laser beam mark is in the center of the nozzle outlet. Set the maximum power to 10%, put transparent tape on the tip of the nozzle, and press the pulse button on the operation panel of the ...
THE CO2 LASER POWER SUPPLY DOES NOT GENERATE THE LASER BEAM, check the input voltage and the LON1 signal / Daniel
THE CO2 LASER POWER SUPPLY DOES NOT GENERATE THE LASER BEAM, check the input voltage and the LON1 signal If the laser source is not generating the laser beam it may be because there is no input voltage at the laser Power Supply; to check measure ...
La fuente láser de CO2 no genera el Haz láser, chequear el voltaje de entrada y la señal LON1 / Daniel
LA FUENTE LÁSER de CO2 NO GENERA EL HÁZ LASER, chequear el voltaje de entrada y la señal LON1 Si la fuente láser no está generando el rayo láser puede deberse a que no hay voltaje de entrada en la fuente láser para revisar mida con la ayuda de un ...
Laser tube operation check for the warranty claim / Daniel
In the next video you can see the procedure https://youtu.be/IjSVHo0gBU4 To check the status of the laser tube follows the next steps: Step 1 Place a piece of acrylic in front of the tube. Step 2 Set the laser Max Power on the machine at 50% Step 3 ...
¿Qué hacer si no hay salida láser del tubo? / Daniel
¿Qué hacer si no hay salida láser del tubo? En el siguiente video puede ver el procedimiento para revisar si no hay salida láser en el tubo https://youtu.be/ISZg6fgLD6U 1- revise que el chiller (refrigerador) esté encendido sin alarmas 2. revise el ...
How to use the autofocus sensor / Daniel
Please check the video to see the procedure: https://youtu.be/qJSVMs6g9Lk To use the "autofocus" sensor, follow these steps: Step 1 Place the laser head on the material to adjust the focal height Step 2 Press the Focus Button in the operation panel ...
Medir la altura focal con el sensor de autofocus / Daniel
Para utilizar el sensor de "autofocus" siga los siguientes pasos: Paso 1 Ubique el cabezal sobre el material que va a ajustar la altura focal Paso 2 Presione el botón "focus" desde el panel de operación y confirme con "enter". Nota: Observe que la ...
How to change the screen mirror mode on the Ruida Operation Panel / Daniel
How to change the screen mirror mode on the Ruida Operatio Panel To change the screen mirror mode on the operation panel, follow the next steps Step 1 Press the menu button and select the option "Controler Settin" and confirm with "enter" Step 2 ...
Como cambiar el modo de screen mirror en el panel de operación Ruida / Daniel
Como cambiar el modo de screen mirror en el panel de operación Ruida Para ingresar cambiar el modo de origen en el panel de operación siga el procedimiento Paso 1 Presione el botón de menú y seleccione la opción “controler Settin” y confirme con ...
4 - Fácil calibración de espejos de una máquina de CO2 / Daniel
Fácil calibración de espejos de una máquina de CO2 En los siguientes videos puedes observr como hacer la calibración de los espejos en las diferentes posiciones Pulso en el primer espejo https://youtu.be/UkZWNYLiJ9A trate de obtener que los dos ...
3- Fácil conexión del equipo auxiliar de una máquina de CO2 / Daniel
Fácil conexión del equipo auxiliar de una máquina de CO2 Para conectar el equipo auxiliar de una máquina de CO2 observe los siguientes videos Conexión del extractor de gases https://youtu.be/LgQv8qLtglM Conexión del compresor ...
2 - Fácil instalación del tubo láser de CO2 / Daniel
Fácil instalación del tubo láser de CO2 Para instalar el tubo láser de CO2 en la máquina Force observe el siguiente video https://youtu.be/wS2Guy7RXgw
1- Fácil nivelación de la mesa de trabajo y la máquina / Daniel
Fácil nivelación de la mesa de trabajo y la máquina Para nivelar la máquina y la mesa de trabajo observe los siguientes videos Colocar las mesas de cuchillas y panal de abeja https://youtu.be/_sasEbl4BG0 Para nivelar la máquina ...
2- Easy CO2 Laser Tube instalation / Daniel
To install the laser tube, follow the next video https://youtu.be/ZD3TNf99ZHs
3 - Easy CO2 Auxiliary Equipment connection / Daniel
To connect the auxiliary equipment of a CO2 machine follow the next videos Exhaust fan connection https://youtu.be/5rzzkRV7fWA?list=PLXWt--vtyu_xh-fNWXevHN537tsZUN3LP compressor connection ...
1- Easy Machine and Worktable Leveling / Daniel
To leveling the machine and the worktable follow the next videos To place Knife blades and honey comb https://youtu.be/JrrI6uHG49o To level the machine https://youtu.be/1N5zerEiXuE To level the worktable https://youtu.be/xj9Kzh8Qhkk
4- Easy CO2 Mirrors Calibration CO2 Machine / Daniel
First of all, you need to level the machine and the laser tube, next step is to check the alignments of the laser beam So in the next videos, we show you how to do it. Pulse in the first mirror https://youtu.be/0xBg7ZNLHZY Try to get the two pulses ...
Cleaning the mirrors on a CO2 laser engraving and cutting machine / Daniel
In the following video you can watch the procedure of changing or cleaning the mirror of a CO2 machine https://www.youtube.com/watch?v=pxIulxX5udA To clean the mirrors of a CO2 machine, follow these steps: Step 1 Identify the safety ring that ...
Next page